Marvell, the global leader in integrated chip solutions, announced on the 29th that ZTE will soon mass-produce a series of EPON products based on the Marvell AVANTATM series of processors in the Chinese market. This result was achieved just two years after the two companies signed a strategic partnership in the field of optical fiber FTTX solutions, and successfully passed the field test of China Telecom. All products comply with the mainstream carrier-class requirements of EPON products and are available immediately.
Marvell AVANTA UPON (Unified Passive Optical Network) technology is the world's only single-chip solution that supports three optical fiber protocols, including EPON, GPON, and active Ethernet. At the same time, AVANTA combines Marvell's research and development strength for many years. It is the first solution that has a 1.6GHz CPU and supports energy-efficient Ethernet, 1588v2 and line rate IPv4 / IPv6 / NAT. In addition, the chipset features green dynamic power management and IEEE 802.3az support; SATA 2.0 personal cloud support for video caching and NAS, and full IPv6 support with integrated PP for networking.
"ZTE has always insisted on adopting a set of strict and standardized tendering procedures to protect the company's interests under the principle of fairness and lawfulness. AVANTA is our rational choice after a series of rigorous selections. Many integrated hardware interfaces can help us quickly create and provide compelling services. "Said Mr. Zhu Yongxing, deputy general manager of ZTE ’s fixed network product department." We chose Marvell ’s solution because of its SoC architecture. GPON ’s unified station has been optimized. In summary, AVANTA is a technologically advanced and superior solution that provides a high degree of flexibility for modern broadband design. â€
ZTE is currently the largest PON provider in the Chinese market. In addition, the Chinese market, which is growing at 15% annually, is also one of the fastest growing FTTX markets in the world. Relevant data shows that by 2012, Chinese FTTX users are expected to exceed 50 million. As ZTE continues to launch more powerful single home units (SFU) and home gateway units (HGU) supported by Marvell's multiple PON technologies, the company will have the opportunity to further expand its market share.
"Our cooperation with ZTE not only verified the technical strength of the entire AVANTA product line, but also reflected the huge market opportunities for FTTX technology." Said Paul ValenTIne, vice president of the corporate business group of Marvell Semiconductor, "This also shows that Marvell continues to want to The market-penetrating development philosophy is dedicated to bringing speed and immersive broadband experience to homes and various places. "
3D printing on the pen machine is mainly used in 3 d printing pen, is made from a special custom Dc Gear Motor, mainly used in 3 d printing pen, pen 3 d printing machine has been updated three generations according to the requirements of product.
3D Printing Motor product introduction:
The 3D Printing Motor is based on the deceleration Motor, coupled with supporting gears and ball bearings.The role of the gear reducer is to provide lower speed and greater torque.At the same time, gear box different deceleration ratio can provide different speed and torque.It's mostly rolling.
Features: 3D Printing Motor, small size, large torque, low noise, durable, low energy consumption, customized power design, convenient installation and maintenance;
Simplify design and save space.
Features: usually used financial equipment, office equipment, electronic locks, wireless charger, remote control toys, precision instruments and meters, automobile industry, medical equipment, consumer electronics, household appliances, electric glass doors and Windows, etc., wide application range
Method of use: the best stable in horizontal plane, installed on the 3D Printing Motor output shaft parts, cannot use a hammer to knock, knock prone to press into the 3D Printing Motor drive, may cause damage to internal components, and cannot be used in the case of blocked.
Operating temperature range:
3D Printing Motor should be used at a temperature of -10~60℃.
The figures stated in the catalog specifications are based on use at ordinary room temperature catalog specifications re based on use at ordinary room temperature (approximately20~25℃.
If a 3D Printing Motor is used outside the prescribed temperature range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.Depending on the temperature conditions ,it may be possible to deal with them by changing the grease of the motor's parts.Please feel free to consult with us about this.
Storage temperature range:
3D Printing Motor should be stored ta a temperature of -15~65℃.
In case of storage outside this range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.
Service life:
The longevity of 3D Printing Motor is greatly affected by the load conditions , the mode of operation,the environment of use ,etc.Therefore,it is necessary to check the conditions under which the product will actually be used .The following conditions will have a negative effect on longevity.Please consult with us should any of them apply.â—Use with a load that exceeds the rated torque
â—Frequent starting
â—Momentary reversals of turning direction
â—Impact loads
â—Long-term continuous operation
â—Forced turning using the output shaft
â—Use in which the permitted overhang load or the permitted thrust load is exceeded
â—A pulse drive ,e.g.,a short break,counter electromotive force,PWM control
â—Use of a voltage that is nonstandard as regards the rated voltage
â—Use outside the prescribed temperature or relative-humidity range,or in a special environment.
â—Please consult with us about these or any other conditions of use that may apply,so that we can be sure that you select the most appropriate model.
when it come to volume production,we're a major player as well .each month,we rurn out 600000 units,all of which are compliant with the rohs directive.Have any questions or special needed, please contact us, we have the engineer group and best sales department to service to you Looking forward to your inquiry. Welcome to our factory.
3D Printing Motor,3D Printing Gear Motor,3D Printing Pen Motor,3D Printing Spindle Motor
Shenzhen Shunchang Motor Co., LTD. , https://www.scgearmotor.com